Honda Rincon Owners Manual

If Your Engine Quits Or Won't Start If you have a problem starting the engine or experience poor engine performance the following information may help you. Installation Insert the front prongs into the hooks and press the studs into the grommets on the rear fender. If the gearshif t lever is moved while the vehicle is moving, the transmission may be damaged.


Owner s Manual & Warranty

Page If you choose to have a tyre repaired, be sure the repair work is performed by a professional. If necessary, install new caps. Consult your Honda dealer. Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

After adjustment, check for smooth operation of the throttle lever from fully closed to fully open in all steering positions. Drivers of street vehicles may have difficulty seeing and avoiding you, which could lead to a collision. Always check the terrain carefully before you start up any hill.

Their functions are described on the following pages. Other Inspection Check that the brake lever and brake pedal assemblies are positioned properly and the securing bolts are tight. Check the cables for tension or stress in all steering positions. Take time to read this section before you ride. Insert the breather tube into the handlebar cover hole.

Page Check the air passages for clogging or damage. To climb a hill, take a running start in an appropriate gear and speed for the conditions.

Reinstall the oil filler cap, oil filler cap lid and dipstick. Do not abruptly apply the rear brake by itself. Avoid angles that would cause the vehicle to lean sharply to one side. If necessary, have your Honda dealer replace them.

If the hoses are worn or cracked, have them replaced by your Honda dealer. Ordinary rope is not recommended because it can stretch under load.

Owners Manuals

If one of these indicators does not come on when it should, yeh dil to mila hai mp3 have your Honda dealer check for problems. We recommend that you have your Honda dealer perform these tasks unless you have advanced mechanical skills and the required tools and equipment. Have the tyre replaced by your Honda dealer if possible.

Before Riding Before Riding Before each ride, you need to make sure you and your Honda are both ready to ride. Remember, be sure to take care of any problem you find, or have your Honda dealer correct it before you ride. If A Component Fails If a Component Fails The brake levers or pedal, control cables, and other components can be damaged as you ride in dense brush or over rocky terrain. Never climb hills with excessively slippery or loose surfaces.

Owners Manuals

Page Reassemble by reversing the disassembly sequence. Rider Training Beginning and inexperienced operators should complete the certified training course offered by Honda.

This section gives practical advice to help you deal with a wide range of problems. If a torque wrench is not used for installation, see your Honda dealer as soon as possible to verify proper assembly. The tripmeter has two sub modes, tripmeter A and tripmeter B.

The following load limits apply to standard equipment only. Drive D Use this position for normal riding.


Tyres Always select your riding area with care. Page Wipe up spills immediately. If the guard and plate bolts are loose, tighten them securely. The items listed on this page are described in this section. Be prepared to stop and add more coolant or water.

Know how to operate all the controls. Lubricate the cables with a commercially available cable lubricant to prevent premature wear and corrosion.

Owner s Manual & Warranty

Instructions for other components are presented in other sections of this manual where they will be most useful. Valves For those who are mechanically proficient and have the proper tools, instructions on adjusting valve clearances are given in the official Honda Shop Manual. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. Install the oil filler cap.

Reinstall the drain tube, securing it with the clip. Make sure all bolts and other fasteners are secure. Make sure the accessory does not obscure any lights, reduce ground clearance, limit suspension travel or steering travel, or interfere with operating any controls. Adjustment is done by turning the adjusting nut.

Make sure that the brake cables, brake arm, spring, parking, and fasteners are in good condition. Check that there are no oil leaks.

Use only a non-abrasive polish or wax made specifically for motorcycles or automobiles. Page Cuts, slits, or cracks in the tyres. Also make sure the fuel fill cap is securely fastened. Use mainly the rear brake to control speed. Turn the adjuster to obtain the correct freeplay.

Honda Owners Site

Fuel If pinging or spark knock occurs at a steady engine speed under normal load, change brands of petrol. Important Safety Precautions Keep cigarettes, sparks, and flames away from all fuel- related parts. If you replace the fuel fill cap, use only a Honda Genuine replacement part.

Practice the techniques outlined in this section on level ground and at low speeds until you are confident in making turns. If you have a tyre professionally repaired at a non-Honda facility, we recommend that you have the work checked by your Honda dealer. Any extensive work requiring additional tools should be performed by your Honda dealer.